鋁藝大門已經被廣泛應用在我們的生活中，而對于鋁藝大門的使用你了解多少？山東鋁藝大門出現關不上自然要找出其應對方法，這樣才能讓其使用的時間更長。而對于山東鋁藝大門出現關不上的解決方法及應對方法咱們一起看看：

　　如果出現啟閉門窗時有阻滯現象，開關需要很大力氣，框扇搭接寬度小，周邊縫隙不均等現象時，一般是由以下幾個因素造成的：

　?。?）門窗框或扇變形，密封條松動脫落。

　?。?）五金配件損壞。

　?。?）安裝質量差，超出允許偏差甚多，又未予及時調整。

　　1、防治措施：

　?。?）門窗安裝要符合安裝工序，隨時檢查和調整每道工序的安裝質量。

　?。?）窗框及窗洞均要劃出中線，窗框裝入洞口時要中線對齊，框角作臨時固定，仔細調整窗框的垂直度、水平度及直角度，誤差應在允許偏差范圍內。

　?。?）鋁藝大門扇入框前應檢查對角線及平整度偏差，入框后要用鋼板尺、塞尺檢查框扇的搭接寬度、周邊縫隙，直至符合要求。

　?。?）正確安裝五金零件，發現損壞應及時更換。

　?。?）做好成品保護及平時的使用保養，防止外力沖擊，不得懸掛重物，致使門窗變形。使用時要輕開輕關，延長其使用壽命。

　　2、五金配件損壞

　　塑料門窗五金配件損壞一般表現為：五金配件固定不牢固、松動脫落，滑輪、滑撐鉸鏈等損壞，啟閉不靈活。

　　造成五金件損壞的原因：五金配件選擇不當，質量低劣；緊固時未設金屬襯板，沒有足夠的安裝強度。

　　防治措施：

　?。?）滑撐鉸鏈不得采用鋁合金材料，應采用不銹鋼材料。

　　（2）用緊固螺絲安裝五金件，必須內設金屬襯板，襯板厚度至少應大于緊固件牙距的兩倍。不得緊固在塑料型材上，也不得采用非金屬內襯。

　?。?）選用五金配件的型號、規格和性能應符合國家現行標準和有關規定，并與選用的塑料門窗相匹配。

　?。?）五金配件應最后安裝，門窗鎖、拉手等應在窗門扇入框后再組裝，保證位置正確，開關靈活。

　　（5）五金件安裝后要注意保養，防止生銹腐蝕。在日常使用中要輕開輕關，防止硬開硬關，造成損壞。

　?。?）對寬度超過1m的推拉窗，或安裝雙層玻璃的門窗，應選擇雙滑輪，或選用滾動滑輪。

　　通過以上的了解，你知道鋁藝大門使用注意事項了吧！而需要鋁藝大門找安誠鋁藝大門，山東鋁藝大門提供優質的鋁藝大門，鐵藝大門，別墅大門等，讓你擁有好的鋁藝大門是我們一直以來的需求，那么對于鋁藝大門的使用你應該知道了吧！

Aluminum art door has been widely used in our life, and for the use of aluminum art door how much do you know? Shandong aluminum art door appears not to close naturally to find out how to deal with, so that it can be used for a longer time. For shandong aluminum arts door appears not closed the solution and countermeasures let's see:

If the opening and closing of doors and Windows has blocking phenomenon, the switch needs great strength, the frame fan lap width is small, the surrounding gap is not equal, generally caused by the following factors:

(1) the door or window frame or fan is deformed, and the sealing strip becomes loose and falls off.

(2) hardware accessories are damaged.

(3) the installation quality is poor, much more than the allowable deviation, and not timely adjustment.

1. Prevention and control measures

(1) the installation of doors and Windows should conform to the installation process, and check and adjust the installation quality of each process at any time.

(2) the window frame and the window hole should draw the center line, the window frame should be aligned with the center line when loading the hole, and the frame Angle should be fixed temporarily. The verticality, levelness and straight Angle of the window frame should be carefully adjusted, and the error should be within the allowable deviation range.

(3) the diagonal line and flatness deviation should be checked before entering the frame of aluminum art large door fan. After entering the frame, the lap width and surrounding gaps of the frame fan should be checked with steel plate ruler and feeler until it meets the requirements.

(4) correct installation of hardware parts, found damaged should be replaced in time.